Cookie Img
Send Inquiry Send SMS    Call Me Free
Home » Products » Sealants » POLYSULPHIDE BASED SEALANT

POLYSULPHIDE BASED SEALANT

POLYSULPHIDE BASED SEALANT
POLYSULPHIDE BASED SEALANT
Product Code : 007
Brand Name : HIND SEALANT PS
Product Description

Hind Sealant PS is two-component system. After mixing two components, the mixed material provides a strong
and highly elastic sealant through cross-linking process. It is available in two grades. Gun grade or non-sag-type
is applied for vertical and inclined expansion /contraction joints & pour Grade type for horizontal joints.
Conforming to IS 12118 – 1987 & BS – 4254 – 1983. Also available as per BS 5212, Part 2


USES
Hind Sealant PS is used both horizontal & vertical expansion contraction joints in all type of building and civil
engineering construction such as:
· Retaining wall
· Precast Concrete Element.
· Underpasses and Tunnels
· Bridges
· High and Low Rise building and wherever a permanently flexible seal is required.
· Hind Sealant-PS pouring grade is designed specially for runways, subways, rigid pavements joints &
horizontal joints

ADVANTAGES
· Economical and Easy to use
· Excellent adhesion to many substrate.
· Non-sag in vertical and overhead joints with Gun grade
· Easy to pour on horizontal joints with Pouring grade
· Permanently elastic
· Good chemical resistance.

APPLICATION


Surface Preparation: All surfaces must be clean, dry and free from loose particles. Correct joint depth can be
determined by inserting compressible board tightly into the joint. Protect surface with a masking tape.


Priming : Hind Sealant PS primer is recommended for the surface namely concrete, brickwork, asbestos,
cement, gypsum board, stone, glass, timber, rigid PVC, anodized aluminum, ceramics etc. Primer is not required
for Epoxy and polyester surfaces.


Mixing : Both components are pre-measured. Use a suitable instrument for mixing. Mix for 8 to 10 minutes or
until smooth and homogeneous material results. Using a pressure gun install the sealant into the joint without
trapping air. Tool-off with a spatula to lightly concave profile. Remove masking tape.


Joint Design:                     Minimum joint depth = 8 mm
                                        Maximum joint width = 50 mm
                                        Width to depth ratio for joints upto 10mm wide = 1:1
                                        Width to depth ratio for joints from 10mm to 50mm = 2:1

 

PROPERTIES
Aspect of comp A                                                                                     White paste
Aspect of comp. B                                                                                    Dark brown paste
Mixed Compound                                                                                     Grey in color
Density                                                                                                    1.55 ± 0.02%
Mixing Ratio                                                                                           Comp A- 92 : Comp B – 8
Movement Accommodation                                                                      ± 20 % of the width
Tensile Strength                                                                                      Minimum 0.3 N./ mm²
Shore “A” Hardness                                                                                  18
Pot Life at 27º C                                                                                      4 hours
Full Cure                                                                                                 7 days
Width to Depth ratio Width                                                                      2:1 depth.
Temperature Range                                                                                 From 5º C to 80º C
Back up materials                                                                                   Polyethylene brityl rod / Thermocol


SHELF LIFE
12 months from the date of manufacture in unopened condition. Keep in cool and dry place.


PACKING
1 kg, 4 kg tin container.


HANDLING PRECAUTIONS
Hind Sealant PS is non-toxic and ingestion to be avoided. Any splashes to the skin must be washed with water.
If contact with eyes occurs, wash well immediately with water and seek medical advice.

 




HINDCON CHEMICALS LIMITED
AN ISO 9001:2008 COMPANY
62 B, Braun field Row, Vasudha, Kolkata - 700027, West Bengal, India
Mr. R. S. Banerjee (Director)
   Call Me Free Offline Send SMS Send Inquiry


Buyers Helpdesk

Let tradeindia.com find Quality Suppliers for you!

I agree to abide by all the Terms and Conditions of tradeindia.com
HINDCON CHEMICALS LIMITED All Rights Reserved.